大连富仕泵业制造有限公司

 

WX系列为离心旋涡泵。 第一级工作轮为离心式，第二级工作轮为旋涡式的两级悬臂式结构。泵的进口为轴向水平方向，出口为垂直向上。离心叶轮用叶轮螺母固定在轴上，而旋涡叶轮可在轴上沿轴向自由移动，以保证旋涡叶轮与泵体、泵盖之间的轴向间隙两侧相等，允许用纸垫调整间隙，泵和电动机合装在共同底座上。轴封可采用软填料密封,也可采用机械密封, 装拆方便；整泵结构为轴对称,通用化, 标准化程度高, 因此安装, 运行, 维护都十分方便；适用于输送温度不高于+150℃，粘度不大于5°E，无腐蚀性的，无固体颗粒的液体。

WX series for centrifugal vortex pumps. The first level work for centrifugal, the second round of the work for the spiral type wheel two-level cantilever structure. Pump of imported for axial horizontal. Export for vertical. Centrifugal impeller with impeller nut fixed in the shaft, and can be on the shaft eddies impeller along the axial move freely, to ensure that the spiral pump body, impeller pump cover with the axial gap between both sides equal, allow paper pad, pump and motor adjust clearance fits into common base. Shaft seal can use soft packing seal, also can use of mechanical seal, raplace singly; The whole pump structure for axisymmetric, universal, standardization degree high, therefore installation, operation, maintenance extremely is all convenient; Suitable for conveying temperature is not higher than +150℃, viscosity is not more than 5° E, non-corrosive, no solid particle fluid.

 

型号说明：Model Explanation 65WX₁-130

65—吸入口径 Imbibe dia.

WX—离心旋涡泵 Centrifugal vortex pump

₁—电源为60Hz，50Hz时不带“₁” Power is 60Hz. Without “₁” when it is 50Hz

130—扬程130米 Head 130m

 

型号 Type	流量Capacity		扬程 Head (m)	允许吸上 高度 HS(m)	转速 Speed (r/min)	郊率 Efficiency (%)	轴功率 Shaft Power (kW)	电机功率 Motor power (kW)	叶轮直径 Impeller Dia. (mm)	泵重/电机重 Weight (kg)
	(m3/h)	(l/s)
65WX-130	6.3	1.8	173	7	2900	28	10.8	15 Y160M2-2	135	70/135
	9	2.5	130	7	2900	34	9.35		135
	11.25	3.1	88	7	2900	34	7.92		135
65WX-140	10.8	3.0	186	7	2900	31	17.7	22 Y180M-2	150	70/180
	14.4	4.0	140	7	2900	38	14.45		150
	18	5.0	94	7	2900	37	12.45		150
65WX-150	17.25	4.8	200	7	2900	34	27.7	30 Y200L2-2	160	70/215
	21.6	6.0	150	7	2900	41	21.28		160
	27	7.5	95	7	2900	40	17.5		160